Differential scanning calorimetric studies on the glass transition temperature of polyhydroxystyrene derivatives containing sorbed water

Poly(4-acetoxystyrene) (PAS) and poly(4-acetoxy-3-methoxystyrene) (PAMS), poly(4-hydroxystyrene) (PHS) and poly(4-hydroxy-3-methoxystyrene) (PHMS) have been prepared. The effects of hydrogen bonding on the glass transition temperatures (T_g) of these polymers have been studied by differential scanning calorimetry. The T_g′s of partially hydrolyzed PAS and PAMS increased with the degree of hydrolysis. Partially hydrolyzed PAS and PAMS are estimated to be random copolymers, judging from the correspondence between the calculated and observed T_g′s of these polymers. The effect of water on the glass transition was also studied, and it was clarified how water adsorbed on the polymers acts as a hydrogen-bond breaker. The ‘critical water content’ is calculated from the decrease of T_g by water absorption, and the relation between hydrogen bonding and T_g is discussed.     

Vertical pneumatic conveying: An experimental study with particles in the intermediate and turbulent flow regimes

Vertical pneumatic conveying was studied in a 3-inch diameter riser 30 feet in length using solids ranging in particle Reynolds number from 100 to 3500. Particle to gas mass flow ratios varied from 0 to 8 and pipeline conditions extended from dilute flow down into the choking region. Average particle hold-up was determined by means of a series of quick-closing valves and particle slip velocity was often found to be greater than the calculated terminal velocity. The reasons for this are examined. Frictional pressure losses in the riser were also determined and compared with literature data. The phenomenon of choking is considered briefly.     

Efficient usage of highly dispersed Pt on carbon nanotubes for electrode catalysts of polymer electrolyte fuel cells

A Pt-deposited carbon nanotube (CNT) shows higher performance than a commercial Pt-deposited carbon black (CB) with reducing 60% Pt load per electrode area in polymer electrolyte fuel cells (PEFCs) below 500 mA/cm². K₂PtCl₄ and H₂PtCl₆·6(H₂O) are used for the Pt deposition onto multi-walled CNTs (MWCNTs), which are produced by the catalytic decomposition of hydrocarbons. The electric power densities produced using the Pt/CNT electrodes are greater than that of the Pt/CB by a factor of two to four on the basis of the Pt load per power. CNTs are thus found to be a good support of Pt particles for PEFC electrodes. TEM images show 2–4-nm Pt nanoparticles dispersed on the CNT surfaces. These high performances are considered to be due to the efficient formation of the triple-phase boundaries of gas–electrode–electrolyte. The mechanisms of Pt deposition are discussed for these Pt-deposited CNTs.     

Effects of 6-anilino-1,3,5-triazine-2,4-dithiol,zinc stearate,and barium stearate on the thermal stabilization of PVC

Individual action and synergistic effect in the combination of 6-anilino-1,3,5-triazine-2,4-dithiol (AF), zinc stearate, and barium stearate on the color stabilization of PVC were investigated. In this system, AF selectively reacts with allylic chlorine atoms in PVC. Consequently, unstable allylic chlorine units were converted to thermally stable allylic structures, thus retarding the development of polyene sequences. Zinc stearate accelerated the reaction of AF with allylic chlorine atoms in PVC, forming the zinc salts of AF (AFZ_nSt, St?C₁–H₃₅COO? ) by reacting with AF. Barium stearate reacted with ZnCl₂ which is formed in the above reaction to give St₂Zn and BaCl₂. Consequently, barium stearate led to the selective reaction of AF with allylic chlorine atoms in PVC and the remarkable retarding effect of discoloration of PVC.     

Formation and Properties of Ln-Si-O-N Glasses (Ln = Lanthanides or Y)

Homogeneous Y-Si-O-N glasses containing 15 or 20 eq% nitrogen (N) were prepared from compositions with Y/Si ratios in the vicinity of that of the lowest eutectic point on the Y₂O₃–SiO₂ phase diagram. The liquidus on the phase diagram shifted toward lower temperatures by incorporation of N. The density, the elastic moduli, and the glass transition temperature of the Y-Si-O-N glasses increased with incorporation of N. This is due to the closer packing of atoms in the glasses by the substitution of N, which is in three-fold coordination with Si, for O which is in two-fold coordination, and the stronger covalent nature of the Si–N bond compared with the Si–O bond. The coefficient of thermal expansion of the Y-Si-O-N glasses increased with increasing Y content, because the discontinuity of the glass network developed with increasing nonbridging anions by the introduction of Y. In contrast, the glass transition temperature and the elastic moduli increased with Y content due to the high coordination of Y for O, and the relatively high cationic field strength of Y. Furthermore, the effect of cationic field strength on properties of Ln-Si-O-N glasses (Ln = lanthanides or Y) is discussed.     

Upper critical solution temperature lubricants for CPVC

Chlorinated polyvinyl chloride (CPVC) is often used in injection molding for products that demand high heat resistance. However, proper control of its flow properties is difficult. To improve flow behavior some internal lubricants are usually used, but they reduce heat resistance of the products. Upper critical solution temperature (UCST) lubricants were found to enhance its flow properties, and also high heat resistance was retained. They act as internal lubricants during processing, improving flow and phase separation during cooling. Therefore they are present essentially as inert filler and thus have little effect on heat distortion temperature.     

Effect of center block structure on the physical and rheological properties of ABA block copolymers. Part II. Rheological properties

The effect of the chemical structure of the center block on the rheological properties of ABA block copolymers with polystyrene end blocks has been investigated. The chemical structure of the center blocks investigated in the present paper are polybutadiene, polyisoprene, ethylene/butene copolymer, ethylene/propylene copolymer and polydimethyl-siloxane. The chemical structure of the center block was found to have a pronounced effect on the rheological properties of the ABA block copolymer melts. The long range relaxation times of these block copolymer melts increases with increasing incompatibility between the styrene block and the center block. However, the rheological properties of the block copolymers are not influenced significantly by the glass transition or the entanglement molecular weight of the center block.     

Graft copolymerization of styrene onto cellulose acetate p-nitrobenzoate by chain transfer reaction

Styrene was grafted onto cellulose acetate p-nitrobenzoate (CANB) by chain transfer reaction of growing polymer radicals to the pendant nitro groups of CANB. A copolymer with a branch for every 17.2 nitro groups was obtained. This result indicates that the pendant aromatic nitro group is more effective in obtaining a graft copolymer by radical mechanism than pendant double bond on the trunk polymer previously reported, where graft copolymers with a branch for several hundred of double bonds are produced.     

Radiation-induced graft copolymerization of mixtures of styrene and n-butyl acrylate onto cellulose and cellulose triacetate

Mixtures of styrene and n-butyl acrylate of various compositions were grafted onto cellulose and cellulose triacetate fibers preirradiated with γ-rays at 0°C in air. Monomer reactivity ratios of the grafted copolymers were found to be different from those of the nongrafted copolymers or those of AIBN-initiated copolymers. The active species initiating the graft copolymerization were trapped radicals for cellulose and peroxides for cellulose triacetate. Kinetic investigations of the graft copolymerization of styrene onto preirradiated cellulose triacetate fibers were also carried out, and it was found that the kinetic scheme for radical polymerization is also applicable to graft copolymerization in a heterogeneous system.